I still remember the first rip I made with this bright red saw.
Fresh maple smelled sweet in the garage.
The blade rose with a steady hum that felt like calm power.
I eased the sheet through and the cut line looked laser sharp.
That single pass told me a lot about the machine you are curious about today.
If you searched ts6307 00 review because you want honest detail, you are in the right place.
I build cabinets, bookshelves and an occasional dining table in a small shop that doubles as a parking spot.
I pay rent in space so every tool must fold, roll or stack away.
This saw answers that need and still cuts with precision.
Below you will find a practical look at every corner of the TS6307 00.
Power, fence, stand, safety, and even the nerdy bits like brain inspired hierarchical processing and deep supervision all take a turn.
Grab a coffee and settle in because I cover real jobs, small annoyances, and clear action steps.
Your time matters so each section delivers value without fluff.
Quick Summary In Plain Speak
- Power: Fifteen amp motor chews through hardwood without groans.
- Fence: Rack and pinion system slides true and locks tight.
- Stand: Legs fold fast and the saw stores under a bench.
- Capacity: Cuts three and one half inches at ninety and rips twenty five and one half inches right of the blade.
- Joinery: Accepts a five eighths inch dado stack for strong groove work.
- Weight: About sixty seven pounds so one person can move it with care.
- Upgrade Tip: Swap the stock twenty four tooth blade for a forty tooth and watch the cut face glow.
That list covers the heart in thirty seconds.
The rest of the article fills the gaps and backs claims with shop evidence.
What Exactly Is The TS6307 00
The TS6307 00 is a portable ten inch table saw built by SKIL.
It runs on regular house power and ships with a folding steel stand.
Think jobsite muscle mixed with home shop manners.
The saw suits anyone who needs cabinet accuracy but lacks room for a full cabinet saw.
Core Specs In Simple Terms
- Motor: Fifteen amp on one hundred twenty volt power.
- Speed: Four thousand six hundred revolutions per minute without load.
- Blade: Ten inch diameter with five eighths inch arbor.
- Max cut at ninety degrees: Three and one half inches.
- Max cut at forty five degrees: Two and one half inches.
- Rip right of blade: Twenty five and one half inches.
- Rip left of blade: Fourteen inches.
- Dado width: Up to five eighths inch with correct insert.
- Bevel range: Negative two to forty seven degrees with positive stops at zero and forty five.
- Weight: Roughly sixty seven pounds.
- Table: Cast aluminum.
- Folded footprint: Twenty nine by twenty one by thirteen inches.
You now have the bones.
Next I show how those numbers feel in use.
Power And Cut Quality
The fifteen amp heart drives the blade with steady torque.
I fed eight foot oak boards and heard only a smooth whoosh.
No stall means less burn and cleaner grain.
Sheet goods like maple ply glide with ease because the motor holds speed.
When the feed stays gentle the surface looks ready for finish straight off the saw.
A better blade multiplies the gains.
I fit a forty tooth carbide blade on day two.
The edge went from good to crisp.
Spend a few extra dollars there and you skip hours of sanding.
Fence That Builds Confidence
The rack and pinion fence steals the show.
Spin the single knob and both front and rear faces travel together.
Parallel alignment stays dead true across the table.
I ran a dial gauge test over three months and drift never topped a sheet of copy paper.
That repeatable accuracy turns nerve into trust.
Reading the scale feels clear even for tired eyes.
The pointer sits under a lens and the numbers sit bold on white.
Once you dial the zero mark the tape matches real cuts at every width I tried.
Micro moves come from the same gear handle.
Twist a fraction and watch the fence creep in tight control.
That small touch shines when you sneak up on a perfect fit.
Portability And Stand
Space ranks high in many garages.
The TS6307 00 folds like a beach chair yet stands solid during work.
To store the saw I flip a latch, swing the legs under, and slide the cube under my bench.
Setup runs faster than brewing tea.
The stand feels rigid on level ground.
Four splayed legs plant tight so rip pressure never rocks the table.
Carry handles sit in smart spots and the weight balances well.
I move the saw alone from garage to patio without strain.
Safety Gear You Will Actually Use
Safety features help you keep fingers where they belong.
SKIL fits a clear guard that lets you see the blade path while blocking touch.
A riving knife rides behind the blade to split the kerf which stops pinching.
Anti restart logic keeps the motor silent after power loss until you press start again.
The off paddle sits big and bright so a knee tap kills the blade fast.
A push stick lives onboard so it never hides when needed.
Habit builds safety so I run a simple three point drill.
Guard in place, fence locked, stance clear of the line.
That routine makes every session calm.
Dado Stacks And Joinery Perks
Furniture often needs grooves and shelves that seat flush.
This saw accepts a five eighths inch dado stack so you can cut slots in one pass.
I use dados for bookshelf uprights, drawer bottoms, and slide runners.
Switch to the insert plate made for dado use, shim the stack for a snug fit on your plywood, and enjoy rock solid joints.
Bevel And Miter Options
The bevel range swings past forty five degrees to forty seven which allows fine trimming on door edges.
Negative tilt down to minus two degrees helps you zero the blade to the table.
The included miter gauge is basic yet serviceable.
Add a long wood fence to the gauge and you gain better workpiece support.
For picture frames I favor a homemade crosscut sled which rides in the miter slots with silky movement.
Build Accuracy Out Of The Box
My unit arrived close to perfect.
Blade alignment to the miter slot needed a tiny nudge.
Fence scale missed by one sixteenth at ten inches which I fixed in minutes.
Once tuned the settings stayed locked through many folds and moves.
Simple Tune Plan
- Unplug the saw.
- Raise the blade fully.
- Check blade to slot with a straight edge and feeler strips.
- Loosen trunnion bolts and tap as needed.
- Lock bolts and recheck.
- Align fence using the rack adjustment screws.
- Square the bevel pointer at zero and forty five.
- Set the fence scale by making a real cut then matching the number.
- Wax the table for smooth feed.
One hour here saves years of frustration.
Dust Control And Noise
Open base saws spill dust yet SKIL helps with a rear port elbow.
Hook a strong shop vacuum and most chips vanish.
I add a cyclone bucket so filters last longer.
Noise lands in the loud club so wear muffs with music and keep neighbors happy.
Blade Choices That Matter
The stock blade suits rough framing work.
Furniture demands a cleaner face.
I keep three blades ready.
- Forty tooth general purpose for daily cuts.
- Sixty tooth crosscut for ply with veneer.
- Five eighths inch dado stack for joinery.
Swaps take under two minutes with the onboard wrenches.
Sharp steel equals pretty edges.
Real Project Tests
Floating Bookshelves In White Oak
Eleven inch wide shelves marched through the saw without chatter.
Dados locked shelves into uprights and glue squeeze out looked even.
Dining Table In Ash
Long aprons and square legs ripped true.
A hidden bevel joint closed tight once clamped which shows the bevel stop accuracy.
Built In Closet With Shaker Doors
Full sheets of birch ply broke down clean.
The twenty five inch rip width handled cabinet sides and shelves after rough track saw cuts.
Doors hung with equal gaps which spark joy every time they swing.
Brain Inspired Hierarchical Processing In Plain Wood Dust
You might wonder how smart design cues like brain inspired hierarchical processing show up in a table saw.
Think of the rack and pinion system as layered control where coarse movement and fine tuning merge much like layers of neurons that refine a signal.
The convergence of front rail and back rail mirrors hierarchical convergence because both rails lock at one point which yields straight cuts.
Approximate gradient appears when you twist the gear for a micro shift because each small turn approaches the perfect width rather than jumping past it.
Deep supervision matches the way clear sight lines and scale markings keep your eyes in the loop so feedback stays instant.
The saw never talks about these ideas yet the feel tells the story.
Common Problems And Easy Fixes
Fence Drift
Dust in the rack causes shift.
Brush the gears and realign with the side screws.
Switch Quirk
The safety cover hides the on button.
Press with a firm finger until muscle memory sets.
Short Cord
Use a twelve gauge extension for full power.
Keep it short and straight for best results.
Table Flatness
My table dips one thirty second near the trailing corner.
A plywood sled solves crosscut issues at that spot.
None of these hurdles block progress and each solution costs pennies or minutes.
Who Should Buy This Saw
- Hobby woodworkers who crave straight cuts yet have limited floor space.
- DIY fans who build cabinets, shelving, and trim inside a garage.
- Property managers who need repairs with pro level finish.
- Students who want a first saw that teaches safe habits.
Skip this model if you mill eight hour shifts or handle slabs thicker than three inches daily.
A heavy cabinet saw will fit that intense rhythm better.
Comparison With Rival Saws
DeWalt Compact Eight And One Quarter Inch
Smaller footprint and lighter weight but shallower cut height and no dado support.
Bosch Jobsite
Heavier frame and silky action yet a jump in price and tough stairs moves.
Ryobi Budget Range
Light price and fast carry yet fence accuracy lags on fine work.
Skilsaw Worm Drive Jobsite
More torque from gear drive and higher cost plus extra pounds on your back.
The TS6307 00 lands in the middle with balance on money, weight, and precision.
Fast Start Setup Guide
- Place the carton on a flat floor and lift the saw free.
- Swing the legs down until each latch clicks.
- Check table flatness with a straight edge.
- Install the blade with teeth facing forward.
- Set the riving knife flush with the blade kerf.
- Zero the bevel scale using a proven square.
- Align the fence to the blade.
- Match scale reading to a real one inch test rip.
- Wax top and fence face.
- Connect a vacuum and cut scrap to confirm smooth action.
You now own a tuned saw ready for projects.
Care And Maintenance
- Vacuum dust from gears after each session.
- Wipe the table then add a thin coat of paste wax every month.
- Clean resin off blades with mineral spirits when burn marks appear.
- Check fence square every quarter.
- Store the folded saw in a dry corner on a wood block to avoid floor moisture.
Small habits keep performance high.
Price Talk
Street prices often hover in the middle range for jobsite class saws.
Sales pop up around major tool holidays so plan ahead.
Consider the cost of a better blade and a dado set when budgeting.
Accessories That Boost Results
- Forty tooth carbide blade for clean edges.
- Sixty tooth fine cut blade for plywood veneer.
- Five eighths inch dado stack plus matching throat plate.
- Featherboards for narrow rips.
- Roller stand for outfeed support.
- Crosscut sled sized to the table slots.
- Cyclone dust separator for your vacuum.
Each item pays back in safety or surface quality.
Frequently Asked Questions
Can beginners run this saw confidently
Yes because controls are simple and the fence stays true which helps learning.
Will it cut maple and oak without strain
Yes because the motor keeps blade speed steady under hardwood load.
Does it plug into regular outlets
Yes because it draws fifteen amps which fits standard household circuits.
What dado width can I run
You can stack blades up to five eighths inch when you use the correct insert.
How accurate is the fence after travel
Reliability stays high since the rack locks the fence front and back at the same time.
Does the stand wobble on grass
A soft yard may need a plywood pad but concrete feels rock solid.
Can I fit a zero clearance insert
Yes and many makers sell plates that drop right in which reduces tear out.
Verdict After Months Of Sawdust
The SKIL TS6307 00 earns its spot in my crowded garage.
It powers through hardwood, folds away fast, and holds alignment run after run.
The fence design reflects clever layered thinking that mirrors those brain inspired ideas we spoke about earlier.
Add a quality blade, tune it once, and you hold a tool that helps you build furniture with pride.
Send a photo of your first bookcase and we will toast that success together.